Showing posts with label project. Show all posts
Showing posts with label project. Show all posts

Sunday, November 24, 2013

Built a Kitchen Buffet in time for Thanksgiving

The latest and greatest project!  I do mean 'greatest' - I think each project is a little better than the last.  This was the first project where I incorporated tile and glass, so pretty proud of how it all came out.

Knocking Off Crate and Barrel
The inspiration for this was a buffet we saw at Crate and Barrel:
The Galvin Sideboard is $1,200 and was also a bit too long for our spot in the kitchen.  I liked the stainless steel top and even looked into buying a sheet of metal, although I haven't worked with bending steel sheet.  In the end though, we decided this piece would be the perfect use of some of our extra backsplash tile.  The Galvin also comes up short in that it has three small storage areas which couldn't hold anything wider than a dinner plate.  We wanted something that could store serving dishes and such.

Construction
I built the buffet starting with the doors for a few reasons.  I had never worked with glass before and routing a slot for it to sit in might be difficult.  I was also cutting the individual boards for the doors with angled corners and anything off of a perfect 45 degree angle could cause the doors to be slightly larger or smaller than planned.  So the thought was to build the doors and then build the box to go around.


The buffet is built out of S4S pine boards from Home Depot.  For some of the larger pieces, I used their pre-joined 24"x48" boards rather than joining several together myself using kreg screws.  Pamela never liked the look of pocket holes, so I wanted to minimize the number of holes I'd have to fill.

My brother had used some Rustoleum Satin Espresso spray paint for a project of his and we really liked the look.  It's not quite as dark as some of the furniture we've purchased, but I might go back and give it a protective finish which may make it a bit deeper.  Working with spray paint was a bit harder than normal paint + paintbrush.  It was easy to cover large areas, but when you care about the finish and drips and paint buildup, it may not be the best way to go.

The top of the buffet uses a 24"x48" board cut down to match the frame.  On top of that, I shaved down some strips to about 3/8" for around the edge of the tile.  Again, the tile is leftover from our backsplash and I think is a nice touch to bring the kitchen together.
Stylin'
The glass is simple 16"x20" sheets from Home Depot and I bought some retainer clips online.  We picked out the handles and hinges from HD too.  The hinges make a big deal about using a Forstner bit to rout the cup holes, but I didn't find that necessary.  I also added some magnetic catches for the doors to help them stay shut.


Sunday, November 3, 2013

Halloween Spider

I was working on another project (post to come soon) but got sidetracked with the Halloween spirit.  The spider below was made from some scrap wood/plywood.
Very spooky!
I had originally planned to make the spider free-standing, but that would likely have been a lot harder than I realized.

We went to a neighbor's Halloween party and a guest actually complimented us on the spider.  Since we are right at the entrance to the neighborhood, everyone sees our house and decorations coming in and coming out.  Now I think we'll have to put something together for Christmas.



Thursday, July 11, 2013

Hanging Flower Display

A triple whammy on this one - made something for Pamela (happy wife), spruced up our living room (happy home), and used only scrap material in the process!

The idea for the... shelf?  display?  came from something Pamela saw on Pinterest - a Floating Vase

We both really liked the idea of adding color to the walls with fresh flowers and set about to re-create.

As I started planning though, there was one thing I didn't like about the design.  The jar is attached by steel wire which is tied together to hold the jar aloft.  It does add a great "floating" element, but I thought this would make it difficult to clean out the jar / change flowers.  You'd need to change the water in the jar as you changed flowers, otherwise you'd get green residue.

My flower display would need to be easy to change.  I bought some large C-brackets from Home Depot, but they didn't make them large enough for the size of jar we wanted to use.  The above jar is a small maraschino cherry jar.  We planned to use larger Ball canning jars.  The idea was a C-bracket installed below as a platform, then another larger C-bracket near the mouth that would prevent the jar from being knocked over.  The look would be a bit more 'industrial' and they didn't have large enough C-brackets so I abandoned that idea.

Instead, we decided to simply build a flush-mounted mini shelf.

I used scrap wood and cut out two matching boards to 18.5" tall by 5.5" wide.  The width fit the jar with some extra space.  The height was targeted to be less tall than our mirror, but was really decided by the available scrap wood I had.
I next cut out a small platform for the jar to sit on.  The jar is somewhat supported below by a small block of wood I cut at a 45 degree angle.  The reality is that the platform is secured by two wood screws which I think would support it just fine.  The angled wood below is a design touch and will also prevent any sagging.

I was excited to also finally use my router on this project to counter sink the screws so it would sit flush with the wall.  I routed out a 1/2" circle around the supporting screw that would hold the display to the wall, as well as in the back so that the screw heads for the platform/support would let the project sit flat.
I used some primer paint I had sitting in the garage after sanding the project down.

Pamela picked some bold flowers and we'll be excited to change them with our mood and the seasons.  She also pointed out that we could do candles in the winter.


Wednesday, May 22, 2013

How to Re-Do A Backsplash

Hire someone.  Well, we did, but at the same time it isn't all that difficult.

Step 1: Plan to have your kitchen out of service for some time
This isn't going to be a weekend project and it'll create a big mess.  You'll also have to cut the power to areas of your kitchen, so you'll be ordering delivery while the kitchen is out of service.

The first real step once you decide you want a new backsplash is to pick the tile.  Home Depot has a good selection and there are a lot of good sites online where you can look at sample kitchens (just search Google for 'backsplash tile').

Pamela's mother was in town and found a Tile Shop nearby.  We went and were really impressed by all the samples as well as kitchen mock-ups.  I think it is important to be able to feel the tile and that's where internet searches fall short.

The tile seemed to run from maybe $5 per square foot all the way up to $25 and above.  The Tile Shop had

Step 2: Demolish your existing backsplash
There's a chance that you can use a pry bar and pop the individual tiles or sets of tiles off.  You'd hope to then be able to simply patch and smooth the existing drywall.  It didn't work this way for us.  If the tile is on correctly, the "mud" is like glue between the tile and the drywall.  When you pull off a tile, you will get big chunks of drywall.

This was really the point at which we decided to hire someone.  Before we had guys come in, we did save some money by taking down some lights that were mounted below the cabinets.  Thankfully, I took an Electronics class in high school which included house wiring.  The additional cost of an electrician would've been quite a burden.
Old Tile and Wires from Lights


We made such little progress after many hours of trying to remove the tile ourselves that we realized we'd never get done or we'd be unable to appropriately fix the drywall leading to an uneven new backsplash.


The guys we hired who had done this many times said that they rarely see situations where the tile comes off easily.  Instead, they plan on completely cutting out the old drywall and replacing it with fresh drywall.

New Drywall Up

New Drywall
 It's a pretty simple process - pry or break off some tile around the edges then use a cutting tool to take down the whole wall.  You then measure and cut new drywall and screw it into the studs.  Viola!  You don't need to prime or paint this, because it'll soon be covered.

Step 3:  Install new backsplash
Again, we outsourced this, but I will provide the quick run-down.

First, layout and measure the tile.  You'll then need a wet saw to cut the tile as you have to leave openings for the different switches and outlets.

Once everything was cut and tested for fit, they mixed the mortar ("mud") and smoothed with a trowel.  The mud dries quickly so you need to do smaller areas and work quickly.

After all the tile is up, don't worry if things don't look perfect - the imperfect spacing between tiles or groups of tile really disappear once you grout the tile.

Pick a grout color, mix it and apply.  It dries after 20 minutes or so, then you can remove the excess with a sponge and water.

Step 4: Re-install switches, outlets, and lights
Our old switches, outlets, and respective covers were a taupe color while the new tile and grout called for white.  Pamela and I worked together to replace all the fixtures.  Make sure you kill the power from the breaker in the basement!

Step 5: The Big Reveal!
Here's the old (picture is from the online listing when the home was for sale)
The Old

The New

Boom! Backsplash'd
And the lights work!
Lookin' Good!

Sunday, January 13, 2013

This is why you buy a house

Boom!

When we started thinking about getting a house I had dreamed of having a basement with high ceilings where I could swing a golf club.  Our basement doesn't have that, so I couldn't make a full swing.

Pamela's parents got me a long indoor putting green last Christmas which I've kept in the basement.  This Christmas, Pamela got me a driving range mat so it was only a matter of time until I cleared out enough space in the garage / workshop.

After completing Walt's coffee table and organizing all my scrap wood into a big junk pile, I now have enough room.

Now if I could only teach the dogs to act as my ball return...

Sunday, December 30, 2012

Project - Coffee Table

This project was the first where I was building something for someone else.

My brother wanted a new coffee table for a birthday gift, so we traded some e-mails on design features.  He found a coffee table online that he liked:
Altra Coffee Table - the model
The other key aspect of the design was to utilize the sheet of glass from his current coffee table.  The one in his apartment gets a lot of use, and over time, the wood would have a hard time holding up to all the wear and tear as well as food/liquid spills.

For this project, I decided to use S4S pine (squared on four sides) rather than dimensional lumber like I had used on my own dining table.  Dimensional lumber's edges are rounded, so when you join two boards together to make a table top, for instance, you get seams between the boards.  With the dining table, these seams are a key area for food and crumbs to fall into and it is tough to clean out.  Given that the coffee table would use a sheet of glass on top, this wasn't an issue.  It does create a different aesthetic, and in this case, I was trying to closely match what the customer wanted.

The table top and the underside of the table were created using 3 boards joined together to make a flat surface.  The storage drawers sat on an under-mount drawer rail.  I hadn't used under-mount before and they are harder to find - I had to order from Amazon rather than get them at Home Depot.
Something's amiss
If you look carefully, you'll see that the opening I cut in the drawer face is off-center.  I guess I wasn't paying attention and centered the cutout at 11.5" for a 21" drawer face.  Oops.  I had to re-do the faces which wasn't a problem since I had extra wood.

This was probably the first time I've used a protractor since middle school geometry.  I did not calculate the radius, diameter, or length of an arc, so I hate to disappoint any geometry teachers reading this.  The protractor was great for sketching out the right arc that I wanted.  I had tried using an upside down bowl or plate as a stencil (don't tell Pamela), but didn't like the sizing.

The table came together pretty well and I was very impressed with the color that came from the Minwax Polyshades Espresso.  I will be sure to not do much staining in the winter though - it doesn't apply as smoothly and you are a lot more likely to get streaks and build-up.

The last step was adding a felt liner to the drawers.  I got to play with a hot glue gun which was a lot of fun.

Pictures of the final product are below.  I like the way it came out although it took me a lot longer to deliver than I would have thought.  Thankfully the customer was okay with the delays.








Wednesday, July 4, 2012

How to fix your dryer... maybe

A Little History
A few weeks before we closed on our home, a hurricane hit the northeast.  We found out the basement was significantly flooded due to overflow from a nearby stream.  Until the day of closing, we were told that the basement was treated and all the important equipment was fine.

At closing, we were told the dryer didn't work.  While it took some work, we were credited with what we believed to be the fair amount for the dryer.

The dryer actually worked fine at first, but conked out within a few weeks.  We used the money to call a appliance repairman and he identified a broken igniter as the problem.  Time and parts cost a bit over $200, but we were still in the black.

Flash Forward to Today
Pamela and I returned from our honeymoon with loads of laundry to do.  Pamela went first but noted the dryer was taking forever to dry her clothes.  Because we'd been through some issues before and I'd sat with the repairman, I knew a few things to check.  The latest problem was different, but I am happy to report that I was able to solve it.  I figured I'd write a few points below that might help you save on repair costs.

How to Maybe Fix Your Dryer
This really applies to the following symptoms which seem to be the most common:  your laundry either takes too long to dry or doesn't dry at all; you open the dryer while it is running and you note that the air inside is not hot.  I am also more specifically referring to a gas dryer.

  • Your dryer likely has its own diagnostics that you can run.  Find the directions in your owner's manual - if you don't have the manual, they are often posted online on Scribd or elsewhere, so just do a search
  • Diagnostic
    • The diagnostic may point you to the problem right away, but in my case, it did not
  • Run the dryer with the door open by pressing in the door switch
    • Put your hand by the lint trap - if there's no suction, you may have a clog in the lint trap, in the exhaust pipe within the dryer, or in the exhaust exiting your dryer going outside
    • You can disconnect the exhaust pipe in the back to see if air is flowing smoothly within the machine
    • If so, check the exhaust vent outside of your home - have birds made a nest?
    • Clogged exhaust can lead to overheating or to your dryer shutting off the heat pre-maturely
  • If that doesn't solve your problem, take the top cover off the dryer
    • Turn the dryer on and look down into the machine (best to do in the dark)
    • Do you see a glowing light come on?  If not, your igniter is likely broken and you'll need to buy a replacement
    •  
    • If your ignitor does glow, do you hear your gas come on?  If not, the most common failing piece is the gas valve coils.  Many companies sell these parts ($10 to $15), but some only sell the entire gas valve assembly (>$100) and you'll likely need a plumber to come in because this will require messing with your gas connection
    • If your ignitor comes on, and your gas comes on, but quickly turns off, this means one of two things.  Your gas valve coils may be bad - they may turn on but under electrical load they fail.  Alternatively, this could be a signal that your thermostat needs resetting or replacing.
    • Ignitor
      • Resetting the thermostat is the simplest.  You'll need to take off the front cover to access the thermostat which is likely near the heat tube.  Search on Google for your specific model and replacement parts.  Sites like Appliance Parts Pros have the schematics of your machine (which can also be found in your owner's manual) which should help you locate the thermostat.
      • Be sure to unplug the machine before you reach in there, then find the thermostat button and hit it.
  • You'll find on the web that there are additional tests you can run on the individual parts to see if they are malfunctioning, but they most often require a multimeter.
When our dryer broke the first time, we never got any heat.  The repairman showed me the broken ignitor - the coil was clearly broken about halfway up and therefore electricity wouldn't run through it to heat it up and ignite the gas.

This latest foray was luckily solvable by resetting the thermostat.  I ended up disassembling almost the entire dryer and ended up with 6 spare screws once I had pieced it all back together.

Sidenote
The internet is incredible - I couldn't even figure out how to remove the cover of the dryer on my own.  I'd like to note all the helpful sites, but there were too many sites that added just a little bit of info which helped me along the way.  One thing I will gripe about though - Fixya.com is the worst website ever.  It can contain good information, but it is difficult to navigate and it seems they just want you to click a lot to sell ad impressions.

Sunday, January 8, 2012

Projects Galore

We've been getting a lot done around the house over the past few weeks.  I finished the back of my first chair, and I've also built the seat, but I don't have the right screws to attach the seat to the chair frame.  Therefore, it'll be a few more days until the chair comes indoors for good.

A few projects that have been completed:
Bought and installed a chandelier
Didn't get electrocuted
We've been pretty lucky in our trips to West Elm.  We bought our sectional sofa for a big discount because it was the floor model and was no longer being carried by the store.  We've been looking for a hanging lamp for the kitchen for some time, but hadn't found anything we were in love with or at a reasonable price.

This weekend, we found this chandelier (not sure what constitutes a chandelier, but West Elm called this one) in the store.  It was originally priced at $250, but on sale for $150.  A clerk told us they weren't carrying any more, so they offered to sell the floor model to us for $75.  Done.

While these kinds of savings are hard to come by, I think you can come across opportunities like these, although it takes time and luck.

Unfortunately, installing the chandelier was a gigantic pain, which was all our fault.  I bought a voltage tester for $5 because we weren't sure which breaker controlled the wiring.  We shut down the power, installed the lamp, then turned the power back on.  When that didn't work, we hit the wall switch but to no avail.  We then undid all the connections, took it down, and then re-wired it.  We probably did this three times over the course of an hour.  It was a special kind of torture because it required one person to hold the lamp up to the ceiling while the other twisted the wires together, put on the electric nuts, and screwed the casing back together.

We were ready to quit, but Pamela insisted we give it one more time.  While I was holding the lamp up, I had an epiphany - we kind of assumed the wall switch we were hitting was correct, but we couldn't be sure.  On the other side of the room was another switch with a dimmer which we had never used before.  Lo and behold, that did the trick.

Replaced boiler pilot light
This wasn't a DIY really.  The pilot light on the boiler which supplies heat to the house went out twice in two weeks during the coldest days.  Pamela came home to a cold house and a nearly frozen dog.  We found instructions online to re-light it, which wasn't much of a challenge, although any time you are playing with gas, exciting things can happen.

Unfortunately, since the pilot went out twice in a short period of time, we figured we'd need to have it looked at by a professional.  The thermocouple was shot, which is a pretty standard problem that is expected to happen every few years.  The $200+ bill was a bit of a surprise.  $30 part and $170 for the one hour of service.  Ah, the joys of homeownership.

Built an equipment drying rack
This was a fun project that took all of 30 minutes.  10 feet of 1" PVC costs $3.  Joints and end caps cost up to $1 each.  Now my gear won't sit in my hockey bag for a week fermenting in between sessions.
Hockey scarecrow

Sunday, November 20, 2011

Project - Dining Table

Mission accomplished!

I wrote back on October 30th that I was building a dining table which needed to be ready for Thanksgiving. It took right around three weeks, but today the table moved into the house and was assembled. We even ate our first meal at the table tonight!

Here she is in all her glory:


Project Plan
I held onto the different receipts from Home Depot so that I could tally up the costs.

I went to the 'dimensional lumber' section for the wood this time and picked out boards made of Douglas Fir.  The boards are more often used in framing for a house rather than the furniture inside of it, but with a good lot of sanding, they can look really good.  The total cost for all the wood was around $60.  The real difficulty was that these boards have lots of imperfections after being run through the different machines at the mill.  They often have ink stamps on them too.  Since I wanted to stain the project rather than paint it, this required extra effort.  The various nicks and other imperfections that I couldn't  sand out generally added to the 'character' of the table.

I used Minwax Polyshades, which is a stain and polyurethane finish all in one.  The color we chose was Mission Oak.

For assembly, I used my Kreg Jig for all joints.  Again, the Kreg Jig was really what inspired me to get going in creating pieces out of wood as it is a simple but good looking way to join wood.

Including wood, screws, stain, wiping rags, sand paper, rubber gloves, brushes, steel wool, and various other items, the total bill came out to just under $150.  I'm really pleased to have a great looking dining table for that price.

Quick Step-by-Step
After buying all the wood, I took it home and began making all the requisite cuts.
All the boards

I was so excited to get going on this project that I made a stupid mistake right away.  The table top required five long boards, but I cut six.  That screwed up another piece I needed to cut, because now I had already divided that board into one too long piece and one too short piece.  So, I had to go back to HD to buy another board.  Not terrible, but a waste of $7.
All cut up
I think the most important part early on was to cut the legs correctly.  If you screw this up, even slightly, you won't know how the table sits until close to the end.  This I found out the hard way.  I really focused on making sure the base of the boards on the legs were even on the bottom, but I left the tops with some variation.  The best thing you can do is to stack several boards and cut them at the same time. 

After all the cuts were made, I drilled endless holes with my Kreg Jig.  Knowing this project was going to be heavy itself and having to support weight, I erred on the side of drilling too many holes for extra joints.  As you are preparing to drill the holes, you need to picture the final project and decide which boards will go where, which side will face up/down, etc.  I really enjoyed this part - deciding which were my favorites and assembling them in my head.  I think the smarter move would have been to fully plan this out before I started making cuts.  As I mentioned above, when using wood that isn't S4S (squared 4-sides - meaning it is completely smooth and looks good on all sides), you'll find blemishes that will force you to maybe hide an ugly side of a board. 

I assembled the long boards into the table top and added a perpendicular board at the end
Table top almost done
The one breadboard (the perpendicular board) pictured above was perfectly flush, but the other side had one board that was short by maybe 3/8".  I then had to take my circular saw and cut off 3/8" from the assembled table top to ensure the other breadboard would attach and be flush.  This threw off a lot of the dimensions of the table, so I now had to make adjustments to the plan.

I next assembled the two legs and the frame separately.  The tabletop itself was already heavy and I began to realize how much of a pain it would be to put this all together myself.

Next came seemingly endless sanding.  I'd read online, and now recommend myself, that you either sand before you begin assembling, or sand once you have a few boards together.  By doing so, you'll make it a lot easier on yourself if you only have to maneuver a single or a few boards rather than an entire tabletop.  I used a hand sander as well as an electric finishing sander.  Sanding by hand was strenuous, but worked a lot better than the electric sander.  I started with 60 grit paper to sand off the real rough spots or ink markings.  Then I moved down to 120 followed by 220 grit paper to get the project ready for staining.
Frame laid out
I then finished assembling the pieces to leave me with a table top + frame and two legs.  The legs wouldn't be attached until I was done and the project was in the house.

This was my first attempt at staining and it could have gone a lot more smoothly.  I watched a few videos on YouTube about staining and decided I would use a rag with stain to apply the stain to the wood.  Staining is different from painting and I wish I understood that better when I started.  Your job is to apply the stain to the wood, let it soak into the pores, then wipe away the excess.  I used a cloth soaked in stain to apply the stain, which is a fine method, but what I didn't do was wipe off the excess as soon as I should have.  This led to some splotching.  For my next project, I will apply with a brush and use the cloth for wiping.

After the first layer of stain was on, the project needed to sit for 6 hours.  Following that, I sanded the entire project again using 000 steel wool.  This helps even out the stain and opens the pores up again to accept more stain.  I next gave the project a second coat.

The Minwax can says that two coats are recommended.  If you want to make the project darker, you can add subsequent coats after you hit it with the 000 steel wool, which I did.
Final stain
The project was pretty much done - I thought.

Today, my brother came over and provided the other set of hands needed to move the table into the house and flip it to attach the legs / flip it back upright.

Unfortunately, once attached, the table had some wobble to it.  This was really caused by two things - 1) the top of the legs weren't 100% even and 2) I focused on making sure the table top was flat, but the underside was a bit uneven.

After a lot of passes with the level, I realized that even if the legs were 100% even, the way they attached to the tabletop could leave them still uneven.  So, I feel like I cheated, but I ended up attaching adjustable feet to the bottoms of the legs.  I knew I'd be adding something underneath in order to protect our wood floors anyway, so why not kill two birds?

With the adjustable feet attached, the table is now steady and sturdy.  We ordered sushi and everyone ate at the table.

What's Next
For Thanksgiving, the six attendees will either sit on the two red chairs we own or on folding chairs.  Soon after though, I am going to try and build four wooden chairs and a long bench to match the table. Should be fun!

Sunday, October 30, 2011

Dining Table - It Has Begun!

Today I started my next wood project - building our dining table.  Here's the wood:
Douglas Fir
I'm sitting at the desk that I built as I type this (start and completion).  It hasn't fallen down and still looks good!  That's given me enough confidence to take on this larger and more important project.

The big difference is the deadline - we are having family over for Thanksgiving and we need somewhere to eat dinner!  The pressure is on.

I decided to create the design on my own - I looked around online with Pamela for tables for sale that we'd like to imitate with our creation.  We borrowed a little bit from several designs we like.  I sketched out the layout on the computer and put together complete plans (well, not step by step).

I'll be sure to post with progress and the project plans.  Here's the wood cut into the pieces I'll need:
Looking good team!
 Wish me luck!

Sunday, October 23, 2011

Project - Building a Desk - Finished!

The desk I built sat in the garage until Saturday morning.  I moved it into the house just in time for our housewarming - at least one person commented positively on the desk without knowing I had built it.  For everyone else, I made sure they knew right away.

Victory!
Scorecard
Having made it through an entire project, I can confidently divide projects into a few different steps and grade myself:
  1. Buying stuff - C or D - I didn't make a smart wood purchasing decision and I ended up making several trips to Home Depot.  For the next project, I think this'll be an easy A.
  2. Cutting the stuff you bought - C+ - unfortunately, I let the 17 year old working at Home Depot make a few cuts so that the wood would fit in my car.  This led to some pieces which were shorter than they should have been.  Before I put together my saw jig, I think some of my own cuts with my circular saw weren't quite straight.
  3. Assembling the cut stuff - B+ - I would give myself an A, but I can't do that on my first project.
  4. Finishing the assembled stuff - B- - not terrible, but not great - see below.
Finshing - There's no such thing as too much sanding!
Once I had the desk fully assembled and the drawer was sliding well, I felt like I had reached the finish line.  How hard could it be to paint something?

First, you need to sand the project.  This helps smooth the project, but also create "grip" for the primer.  You could use a primer + paint, but I went with separate primer and paint.  Primer is generally white or gray.  It is suggested that you use gray if you are painting with dark colors.

So sand, then apply a thin layer of primer.  After it has dried, sand again, then prime again.

Next, sand again before applying paint.  It's really helpful to buy a "tack cloth" which is a cloth... that is tacky.  You bunch it up and wipe the project and it picks up all the little bits of sawdust.  I didn't do this at first, which was a mistake, because as I applied the primer, some spots looked gritty.

When I first applied the paint, I used a paintbrush.  This was also a mistake.  For a rookie, it seems that no matter how hard you try to keep from leaving brush strokes, they'll be there.  And they don't look good.  After a layer of paint, I bought a roller and the results were great.  The problem was that I had a layer of brush-strokes beneath which I couldn't effectively sand away.

In between layers of paint (and you want at least 2 layers) I sanded again.  At this point, you want to use a very fine sand paper and slide it across the project to again, create "grip" and to even out any minor bumps.

Once the paint has dried and you are happy, you'll want to apply a protective finish.  I read that a spray can of water-based polycrylic was the best / easiest.  Let me give you a tip to save you some headaches - you are going to be applying many layers of polycrylic, so spray the project very lightly, let it dry (30 mins) then do it again.

After my first pass with the polycrylic, I looked at the project and thought there were some areas I missed.  So I gave those areas a more focused spraying.  This only led to buildup of the polycrylic.  I tried wiping them with my finger or paper towel, but then the area looked smudged.

After layers of poly, you again need to sand with very fine paper.  Since I had created some smudges and buildup areas, I sanded with a bit more force - in at least two spots, I sanded away the poly and the paint underneath to expose primer.  Ugh!

So now I needed to re-touch a few areas with paint, then hit it all with poly again.  I probably should have re-touched with paint, let it dry, then done it again.  At this point though, the project had been out in the garage for a good week and I was running out of time to show it off at our housewarming.

Feet
As a final step, I drilled some small holes in the feet and added screw-in felt furniture feet.  This would also make it possible to adjust the desk if it wasn't level, although it was.

The feet did left the project off the floor by 1/4" which I felt took away from the look a little.

Summary
All-in-all, passing grades.  The big test was whether Pamela would let me try to build us a dining room table next, and I have received the go-ahead.  So, be on the lookout for dining table posts soon!

Monday, October 17, 2011

Project - Build a Desk

First off, I have to say that none of this would have been possible without the help of Ana-White.com, a site and blog about an Alaskan mother who builds furniture on her own time.  Please visit her site for helpful how-to's and project plans.

Background
Before we even moved in, I began thinking about DIY projects that I'd like to accomplish.  We knew the house would be lacking in furniture, as we were coming from a one bedroom apartment and now had several bedrooms.  Our apartment also had a kitchen island, so we didn't have a dining table or chairs.

I originally intended on building a dining table, but the scale of the project and the daily usage the table would receive guided me to try something a bit smaller first.

In our kitchen, there's a corner space where the seller used to have a desk with a TV on top.  We thought that'd be a great place for a laptop and some stationary outside of the office.  The space available is 40" x 24"

Pamela and I found a plan online that we really liked and thought we could adapt to the space.  See the Simple Modern Desk plan here.

Our version would have slightly smaller dimensions, one large drawer instead of two, and wood boards as a top rather than a single sheet of MDF.

Supplies and Materials
On one of our first trips to Home Depot I got to buy power tools.  I bought a drill and a circular saw, along with nails, screws, and an array of screwdrivers and other hand tools.

If you are in the market for power tools, I suggest buying corded tools if you can.  If you are like me and will be working around the house where you have access to electric outlets and/or extension cords, spending the extra money on cordless tools might be a waste.  Cordless tools also need to be charged and often aren't as powerful (for the same price point).

One of the key enabling tools for me has been a Kreg Jig.  When joining pieces of wood together for furniture, you have several options.  The Kreg Jig, in my opinion, is the simplest and may also be the most attractive visually.  Just peruse a clip on their site and you'll see what I mean.

I purchased poplar boards from Home Depot for this project.  This was a rookie move - I walked up and down the lumber aisles and thought these boards looked best.  They were also labeled as good for furniture.  I didn't realize they were priced per foot, as opposed to many other boards that were priced per piece.  For a 1" x 3" board that was 8 feet long, I probably spent $15 to $20 per board.  With other types of wood I could have spent less than $10 or even less than $5 per board.

Setup
Below is my garage / workshop / man-cave:
Man Cave-y
In the forefront on top of two stools you can see my saw jig.  I use this to make perfectly straight cuts with my circular saw.  The perpendicular board in the center of the photo is used as a guide, I press the circular saw's foot along that board as I am making the cut.  I slide a piece of wood below that board but on top of the jig's base.  You can see the channel that is cut in the jig to the left of the perpendicular board.

Before I had the saw jig setup, each cut was nerve wracking.  Being new to a circular saw, I was concerned I'd make a lop-sided cut or remove several fingers.

Non-Step By Step
For a good step by step, please download the project plans from Ana-White.com.

Since the dimensions of our desk were going to differ, I had to sketch out each section including all the new measurements.  This really saved me a lot of heartache as I realized making a board 1/4" shorter would affect both the length AND the width of the project in several instances.

I also didn't follow the advice on Ana-White.com in allowing Home Depot to cut a few pieces of wood to help them fit in my car.  The guy at HD doing the cutting was probably 17 and had been off on a lunch break.  He came back to a long line of customers waiting to have their wood cut.  I only had him cut a few boards, but he managed to screw one up (I made the mistake of not measuring before I left).  Now that I had one important board that was short, I needed to adapt all the dimensions to fit this board (the alternative was to buy another board and have it cut right, but I was home and ready to get working!).

Here are most of my boards cut down to size (some still waiting to be cut):

Here are the legs mostly assembled:

 Here's the frame:

Fully assembled!:

Priming:

Primed and ready for some paint:

A Few Notes on Finishing
Wood filler is s savior.  It's primarily used to fill cracks and cover nail heads - it can then be sanded and painted.  For my first project, since some boards didn't fit together perfectly, I filled the gaps with wood filler so that they wouldn't be noticeable.

Adding to my rookie mistake on choosing poplar boards, I later found that poplar is very difficult to stain.  My original plan was to stain the desk into a deeper brown / wood color.  I found sites on the internet that said I could use a sealer first, then apply stain although the sites cautioned that the outcome might not be desireable.  I tried this on some scrap and really didn't like the look.  Poplar does paint well though, so that's what we'll do.

We primed the desk and will paint it in the next few days.  We are leaning towards painting it white, but red is also under consideration.  Anyone want to post a comment with their vote?

Summary
The project has taken me two weeks or so.  If I were to do it again, I could probably do it all in one weekend (minus painting).  I'll post again in a few days after it has been painted and moved into the house.  Pamela is very impressed and has given me a free pass to build other things.  There are a lot of other projects around the house that I could maybe build, but the dining table (and chairs) is probably next.